Supermicro x7dbe-x manual

Related sponsored items. Showing Slide 1 of 3. New New New. Pre-owned Pre-owned Pre-owned. Seller Report item - opens in a new window or tab. Seller assumes all responsibility for this listing. Item specifics. New: A brand-new, unused, unopened, undamaged item in its original packaging where packaging is Read more about the condition New: A brand-new, unused, unopened, undamaged item in its original packaging where packaging is applicable.

Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail packaging, such as an unprinted box or plastic bag. See the seller's listing for full details. See all condition definitions opens in a new window or tab. Does not apply. Shipping and handling.

This item will ship to Germany , but the seller has not specified shipping options. Contact the seller - opens in a new window or tab and request a shipping method to your location. Shipping cost cannot be calculated. Please enter a valid ZIP Code.

No additional import charges at delivery! This item will be shipped through the Global Shipping Program and includes international tracking. Learn more - opens in a new window or tab. There are 6 items available. Please enter a number less than or equal to 6. Select a valid country. Please enter 5 or 9 numbers for the ZIP Code. Handling time. Taxes may be applicable at checkout.

Learn more. If anything listed here is damaged or missing, contact your retailer. San Jose, CA U. When LE1 is on, make sure to disconnect the power supply before removing or installing components.

For the ZCR card to function properly, be sure to install it in the green slot. Slot 1 supports up to MHz. The P chipset supports single or dual Xeon bit dual core processor s with front side bus speeds of up to 1. It continues to operate when the system enters Standby mode.

When in sleep mode, the CPU will not run at full power, thereby generating less heat. In addition, the 12V 4-pin power supply - is also required to ensure adequate power supply to the system. See Section for details on connecting the power supply. To prevent damage to your system board, it is important to handle it very carefully.

Always connect the power cord last and always remove it before adding, removing or changing any hardware components. Page 23 3. Do not apply any thermal grease to the heatsink or the CPU die-the required amount has already been applied. Place the heatsink on top of the CPU so that the four mounting holes are aligned with those on the retention mechanism. Page 25 CPU and the heatsink. Make sure that the locations of all the mounting holes for both motherboard and chassis match.

Make sure that the metal standoffs click in or are screwed in tightly. Page Installing Dimms Repeat for all modules see step 1 above. Populating DIMM modules with pairs of memory modules of the same size and same type will result in Interleaved Memory which will increase memory performance.

See Figure for the descriptions of the various control panel buttons and LED indicators. Attach it to the hardware reset switch on the computer case. The 4-pin 12V PWR supply is required to provide adequate power to the system. However, Pins of 4-pin fan headers are backward compatible with the traditional 3-pin fans. The mouse port is above the key- board port.

This feature allows your computer to be awakened by an incoming call to the modem when the system is in the suspend state. This port accepts RJ45 type cables.

This LED will blink to in- dicate a fan failure. A System Management Bus header is located at J Refer to the board layout below for the location. Jumpers create shorts between two pins to change the function of the connector. Instead of pins, this "jumper" consists of contact pads to prevent the accidental clearing of CMOS. To clear CMOS, use a metal object such as a small screwdriver to touch both pads at the same time to short the connection.

The default set- ting is on pins to enable SCSI. See the table on the right for jumper settings. This feature available when three power supply units are installed in the chassis with one act- ing as a backup.

If you only have one or two power supply units installed, you should disable this the default setting with J3P to prevent false alarms. Page Chapter 3: Troubleshooting Chapter 3 Troubleshooting Troubleshooting Procedures Use the following procedures to troubleshoot your system. Note: Always disconnect the power cord before adding, changing or installing any hardware components.

Page Technical Support Procedures 1. Page Frequently Asked Questions Question: What are the various types of memory that my motherboard can support? It is strongly recommended that you do not mix memory modules of different speeds and sizes. See Chapter 2 for detailed Information. When returning to the manufacturer, the RMA number should be prominently displayed on the outside of the shipping carton, and mailed prepaid or hand-carried.

The P Blackford MCH chipset is designed for symmetric multiprocessing across two independent front side bus interfaces. Each front side bus uses a bit wide, MHz data bus that transfers data at Warranty Manufacturer Warranty.

Support URL: www. Click here for full warranty and support information SuperMicro logos are registered trademarks of SuperMicro.