Hills nx 16 user manual

Zone Doubling cannot be used if the option is enabled. See Feature 22 Dynamic Battery Test The Hills Reliance can be programmed to perform a dynamic battery test to verify the condition of the battery for a selected duration the first time the panel is armed or disarmed every day.

The Hills Reliance can also be programmed to perform a missing battery test every 12 seconds. This report will be sent along with the user number that armed the system, if the panel is not disarmed before the entry delay expires. The alarm report will also be sent. See Feature 9 and 16 Expander Trouble The Hills Reliance will report expander trouble to the central station if enabled. Note: The code pads are considered expanders. The number of the expansion devices reported can be found in Appendix 3.

See also Feature 9 and 22 Fire Alarm Verification When enabled, the Hills Reliance will verify a fire alarm by waiting for a second trip on a smoke detector within a specified time before creating an alarm see Feature The communicator will delay for a specified time before reporting the alarm, if a valid code is entered, the report will be aborted, and the smoke alarm verification option will be reset if enabled. If no valid code is entered the alarm report will be reported to the base station.

These events can later be viewed through downloading or the LCD code pad. All reportable events report to the log. Number of Calls and Rings to Answer The Hills Reliance can count the number of calls and rings that must be met for automatic download answering.

See Feature 13 On Board Zone Disable The zones on the main Hills Reliance control panel can be disabled in order to have a completely wireless alarm system. See Feature 22 Partial Mode Partial mode allows system owners to arm only designated partial zones e.

Partial mode encourages system owners to use their alarm system more frequently when the premise is occupied. All other zones will function as normal. See Feature 22 Telephone Line Monitor The Hills Reliance and Hills Reliance 12 have a telephone line monitor that monitors the voltage and current of the telephone line to detect a cut phone line. This condition can also be reported to the central station after the line is restored.

Not available on the Hills Reliance 8. The Hills Reliance will also see an alarm activation if any Twin Trip zone that is continuously faulted for longer than 10 seconds. See Zone configuration Group Table and Features 22, 24, and This section describes how to program the address and area of each code pad as well as the options that are available.

The code pad address allows the panel to monitor and supervise the connected code pads and report code pad communication faults.

The factory default for the Master code is [1] — [2] — [3] — [4] when using a 4-digit code or [1] — [2] — [3] — [4] — [5] — [6] for a 6-digit code.

Enter the [Program Code] Note that older code pads only support up to 48 zones i. Keep this in mind when expanding a site by replacing the panel — some code pads may also need replacing. The value in this function would be [6][0]. Example : For enter [0][6]. Enter the [Master Code] Example: Enter am as [0] — [0] , 7. Note: The clock is a hour clock. Example : 7 minutes after the hour would be entered [0] [7]. The ready light is constant and the partial light will flash.

Lights illuminated indicate the authority levels assigned to this code. An explanation of the lights is listed below:.

Note you cannot set attributes on both sides of the table above e. Arm Only and Activate output 3. The ready light will flash. This moves you to the area enable. The user has access to areas that are illuminated by the LEDs. The illuminated numbers indicate each area where the user has access. To change any of the areas where the user has access, press numbers corresponding to areas where you want to give the user access or deny access. Refer to chart shown below:. Example: If zone LED 2 is lit, then the user is assigned access to area 2.

By pressing the [2] key, the light will go off, denying access to area 2. You may then enter another user number to assign authority level.

Repeat Steps 4 — 8 until you have assigned authority levels to all user numbers. Press the [ ] key to exit the Assigning Authority Level Program. If you desire the end user to be able to add new codes, you must remove the area authority from all blank codes. By faulting any zone, that zone will latch its zone light on the LED code pad, and sound the Chime.

The Chime will continue to sound each time a zone is faulted. Once all zone are tested zone lights lit on the LED code pad go to step 3. Features or Feature numbers are used to locate an option or group of options. Example: Feature 6 contains the communicator format selection and Feature 16 contains area one options. Segments are contained within each feature, there are two types of segments.

The first segment type is referred to as an option select segment. This segment type contains up to eight options that can be toggled On or Off like dip switches. The second segment type is referred to as a numeric segment. Options are contained within segments. An option select segment can have up to eight options. Example: Feature 6 contains the communicator format that has one segment with one option; and Feature 16 contains area one options that has 5 segments with 40 options in total.

You are now in the Program Mode and ready to select the module to program. Selecting The Module To Program: Since all modules connected to the Hills Reliance are programmed through the code pad, the module you are programming should be the first entry. To program the Hills Reliance control panel, enter [0] — [ ]. Other module entry numbers can be found in their corresponding manuals. Any feature can be accessed by directly entering the desired programming feature followed by the hash [ ] key.

This procedure is repeated until the last segment is reached. If the previous feature is desired press the [FIRE] key. To review the data in a feature, repeat the above procedure, pressing the [ ] key without any numeric data entry. You are now ready to enter another programming feature as before. If an attempt is made to program an invalid entry for a particular segment, the code pad sounder will emit a triple error beep beep, beep, beep , and remain in that segment awaiting a valid entry.

Exiting The Program Mode: When all the desired changes in programming have been made, it is time to exit the program mode. If no additional modules are to be programmed, pressing the [Exit] key again will exit the program mode.

The procedure for programming these devices is the same as for the control panel, except the features will be for the module selected. Programming Data: Programming data is always one of two types. The other type of data is a Option selection type. Option selection data is used to turn options on or off.

Use the following procedures when working with these two data types: Numerical Data: Numerical data is programmed by entering a number from on the numeric keys of the system code pad.

To view the data in a feature, a binary process is used. As before, you are now ready to enter another programming feature. If an attempt is made to program a number too large for a particular segment, the code pad sounder will emit a triple beep, indicating an error, and remain in that segment awaiting a valid entry. Option Selection Data: Option selection data will display the current condition on or off of eight options associated with the programming feature and segment selected.

Pressing any numeric key between [1] and [8] for selection of a option, will make the corresponding LED illuminate option ON. You will see that numerous options can be selected from within one segment. This will enter the data and automatically advance to the next segment of the feature.

There are two methods of loading the factory defaults: Method 1 — Enter the program mode using the procedure on page 9, then type [9] — [1] — [0] — [ ]. The code pad will beep 3 times indicating that the loading is in progress. The loading takes about 6 seconds. Method 2 — Enter [9] — [7] — [1] — [3] — [0] — [0] within 10 seconds of power up at any code pad which is not programmed for master mode.

The procedure will default the Hills Reliance control panel even if it is armed. For supervision purposes, the Hills Reliance has the ability to automatically find and store in its memory, the presence of all code pads, zone expanders, wireless receivers, and any other module connected to the data terminal KP DATA whenever exiting the program mode.

To force module and keypad enrolment, whilst in program mode enter [9] — [1] — [5] — [ ] — [Exit] — [Exit] , and wait 12 seconds. Zones can be programmed to be one of 32 different zone configurations zone types.

Configurations 1 to 20 can be modified in the configuration group section of this manual. Configuration groups 21 to 31 are factory set and cannot be altered. Choose one of the 30 default zone configurations to program into each of the zone configuration segments e. Study this table for the appropriate zone configuration group for each zone. Refer to the code pad programming section in this manual. Feature 0, segment 1 is used to enable the 6 digit user code option.

If this option is enabled, the default user 1 code is [1] — [2] — [3] — [4] — [5] — [6]. The Hills Reliance has 99 four 4 digit user codes or 66 six 6 digit user codes, the Hills Reliance 12 has 40 codes, the Hills Reliance 8 has 8 codes. Your email address will not be published. Save my name, email, and website in this browser for the next time I comment.

Find Installer Register as Installer Menu. See all results. Table of Contents. Email Enter your email address. Was This Article Helpful? Next Challenger10 with V8 numbering Chart. Reply to comment. Leave a comment Cancel reply Your email address will not be published. We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it.

Connect to the Note: A 3. If no resistor is used, you may experience voltage leakage into the siren that will cause these devices to output a small signal. Connect the to the KP data terminal on the code pads and the expanders usually blue or green wire. These numbers are for one code pad at the end of the wire. Successfully added to cart. Successfully added to wishlist. Successfully removed wishlist. Thank you for Contacting Us We will respond to you shortly.

Credit Card details saved successfully. Credit Card details updated successfully. Credit Card details deleted successfully. Address Saved. Address Updated. Thank you Creditcard has been saved successfully. Thank you for your payment. Creditcard Payment Transaction has been Failed.. Try again!! Enter Product Configuration Details X. Hills Reliance Login to see your exclusive price. Stock Availability. No stock information to display.

Submit inquiry for license. Please Provide the below details to purchase this product:. End user organisation name. End user organisation address. End user contact name. End user phone. Hardware serial no. Multiple entries to be separated by;.